Hand Cobbler Shoes Repair Sewing Machine Dual Leather Cloth Cotton Nylon Thread

Description

Notice:
Professional machine, please make sure you know how to use it before your order.
Description:
This machine can be used with nylon line and cotton line, can be used with Prince line and other lines, Max. sewing thickness is 5mm.
Can sewing different material shoe by nylon or cotton wire.(Such as cloth shoes , rubber shoes , leather shoes , sneakers , high heels , as well as raincoats , leather bags , cloth , trousers, or other leather products.
Operating Instructions:
1. Preparation before operation:
* Press the foot and avoid the friction between the foot and the pin plate.
* Check the fastening of fixed screws in each department.
* Add oil to each part of the oil.
* The shaking guide plate can be used without the sound of kazak.
2. Threading and lead:
*. Take the shuttle shell and the spindle: shake the guide plate, lift the needle to the highest position, remove the shuttle with tweezers, lift and push the needle plate, and remove the shuttle with tweezers.
* Spindle winding:
Pull off the winding machine, pull out the wire wrap around the center of the spindle for a few weeks into the spool, shake the guide plate to be wrapped around the center of the shuttle, and pull back the winding.
* The center of the shuttle will first transmit the thread of the spindle to the line hole of the shuttle money, and then insert the spindle into the shuttle, and then the thread will be inserted into the hole of the surface to pull the line.
* Put the position of the spindle is hand guide plate, the needle was about to rise, the spindle end to aim at the needle groove, and the thread take 2 to 3 inches long, according to the bed and a half months have flown groove close needle plate again, shaking the market, but the bottom line to the needle plate, passed quickly put the location of the error, the bottom line with online and offline.
* Wearing noodles:
Shake the guide plate, lift the needle to the top position, and put down the foot. Pull out the line head in the coil, thread through the middle shaft, through the thread and line, through the thread spring and thread, enter the hole of the needle, and then pull the line through the needle hole to pull the line head 2-3 inches.
* Leave the front of the line in the left hand (not too tight), and use the right hand to shake the guide plate, so that the needle belt line will pass through the pin hole to draw the bottom line, and together with the bottom line, the machine press the foot gap left behind.
3. Relationship between the bottom line and mending quality:
* Identification of needles.
* Adjust the bottom surface pressure, tight line screw nut SongYa line, use time is too long, there will be a bottom line for too fast, the adjustable or bobbin change line into line, the bottom line, the take-up fixed screw loosening, pick needle bar backward, check whether the bobbin rotating flexible, use sandpaper sanding, tighten the line pressing nut stitch length adjustment.
4. Adjustment of needle spacing
Because the sewing material is different must adjust the needle pitch, when choosing the needle length, only need to screw the needle pitch screw loose, in choosing the needle to be short time, conversely upward move, can.
5. Adjustment of pressure foot pressure
When the pressure must be increased, the pressure must be tightened, and the tension of the tension spring will be increased, and the pressure of the foot will be increased.
6. Handling and sewing of machine needle:
* Turn the guide plate, the needle bar up to the top spin pine needle clamp screw, remove the old needle, insert the flat face new needle rod inside the groove, touch the bottom of the channel of the machine when the needle positioning gear, then tighten the screws.
* Combination of needle and stitching: generally use 18 pin, sewing various kinds of rubber shoes and bag side shoes, such as needle, 14-16, sewing various leather shoes and canvas, etc., with 18 pins.
7. Adjustment of the location of the sotto: many people can't draw the line, the reason is that the position is wrong.
When output spindle is to take off the line, the tail end of the shuttle must aim at the needle groove, the gap from a lot, misplacing of spindle position, not timing will be adjusted, loosen the loose piece with screw rod links, moving rod, can make the tail end of the spindle on the needle groove, then tighten the screw.
8. The adjustment of the needle bar up: in the stage of needle, needle hole should be on the spindle bottom plane, or it should be adjusted, method is to loosen the screw on the small connecting rod shaft, move the needle bar to the right position to tighten again.
Use and maintenance:
Mending shoes machine parts need to go once a day, can guarantee the machine running light, no noise, especially the shuttle tank must be in a bobbin, add oil, lest produce pist and wear and tear, improve work efficiency, prolong service life.
Payment
We only accept the payment through PayPal.
Delivery deail
A
ll USA orders get shipped within 2-3 business day from our CA warehouse directly.P
lease
provide an valid and correct shipping address.
Note:
some are
shipped from our HK warehouse,it will be shipped within 10 days
when payment received.
Import duties and any other fee are not included in the item costs or shipping costs.Buyers are
responsible for those charges.
Warranty & Return
If buyer want to return the product without any problem,buyer should pay return shipping fee.The item must be returned
in good condition and its original packaging and accessories, never installed or mounted.We will not accept returns
after 30 days of delivery date.
About us
We are a professional facotry store.All LED lights use high quality
materal and advanced technology.If you can't find a satisfied paint scheme fairing in our store, please contact
us, we can customize any designs you like.
Feedback
100% Positive feedback, your truely feedback is very important for us
.
We will surely solve the problem for you satisfactoriness (100% communication,100% replacement)
On Feb-28-21 at 23:22:39 PST, seller added the following information: